• 676 Answers SOURCE: Try to reprogram the remotes to the alarm. Have your vehicle key and both remotes ready. The way to do this is as follows: 1. Turn ignition key to run position. Within ten seconds push the valet button 5 times. The siren will give a chirp, indicating that you are in programming mode.

If the author doesn't mind sharing the source code, that would solve the problem too. Of course, best possible solution is for Matlab to include this functionality with built-in functions. Matlab version 7.5 r2007b. Other than cluttering up the command window or the DOS window for the stand alone executables, functionally I have no issues. Though I would agree that someone should generate up to date.p files but then I am not sure if it would make it unusable for people with earlier versions of Matlab. Thanks a lot!

Press the large button on the first remote. A chirp will be given as confirmation. Press the large button on the second remote. A chirp will be given as confirmation. Turn off ignition and remove key.

View and Download Omega K9-Mundial owner's manual & installation instructions online. K9-Mundial Car Alarm pdf manual download. Car Alarm Omega K9-150 Owner's Manual & Installation Instructions. I has a Mitsubishi Pajero mark 2 A 1996 model I install a mundial k9-4 but cannot get the dome lamp to operate with it can.

Alarm will give long chirp indicating exiting program. Both should be working. For the next 48 hours, every time the vehicle is starting the siren will chirp indicating that remotes have been programmed.

After 48 hours this feature will turn itself off. Also keep an eye on the alarm light as it will also blink the number of times as remotes are programmed every time the ignition is turn on. Hope this information helps.

Posted on Mar 04, 2010. I am assuming that you want to disable the system temporarily by putting it in valet mode. You will need to locate the valet button; they are usually installed under the dash within reach of the driver. The button should be black and about 1/2' in diameter.

Pressing and holding the button for 3 seconds while the alarm is disarmed will put the system into valet mode. The system will turn the LED light on steady and chirp the siren to indicate that valet mode has been activated. To exit valet mode, press and release the button. The LED will turn off and the siren will chirp to indicate that you have exited valet mode. The included link is for the manual, see page 8. Nov 03, 2010 . I was very mad because I looked for this code for long time over the web and nowbody know the unlock code for this pleyer but siting in front of it and thinking in all the posibilities i found it.Now I would like to sher it because for me should be no region codes for any player.

All you have to do it's: 1.-Make sure ther are no disc on the tray. 2.-Turn the pleyer on. 3.-Press the select buttom located at the front of the pleyer for about 10 sec. The number of the current region will aper for example (1) 4.-then using the volume control (located olso at front of pleyer) change that number to (0) to make it region free. 5.- Do noting wait about 3 sec. And your player will be region free. 6.-Enjoy the show.

On Feb 29, 2008 . Use this procedure for New Body Style. Close all doors 2. Insert key into ignition 3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down until instructed to release in step 9. Perform steps 5 through 8 in a fairly rapid succession.

Turn the ignition to the ON position (as far as you can go without starting the engine.) 6. Turn the ignition to the OFF position.

Turn the ignition to the ON position (as far as you can go without starting the engine.) 8. Turn the ignition to the OFF position. Release the power UNLOCK button on the door panel. The vehicle should respond by door locks locking and unlocking automatically. ( If locks do not cycle after you let go, not before you let go of the unlock button, then the vehicle has not entered programming mode and you must start procedure over. Remove key from ignition, open drivers door and return to step 1 ).

If the locks do cycle automatically then proceed to step 10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and unlock. This may take up to 30 seconds. Repeat step 10 NOW for each additional remote.

(Including any existing remotes). Turn the ignition to the ON position to exit the programming mode. Test remote(s). Apr 29, 2010 . Close all vehicle doors.

Insert the key into the ignition. Hold down the power UNLOCK button on the driver’s door panel-continue to hold down until instructed to release in step 9.

Perform steps 5 through 8 in fairly rapid succession. Turn the ignition switch to the ON position (as far as you can go without starting the engine). Turn the ignition switch to the OFF position. Turn the ignition switch to the ON position. Turn the ignition switch to the OFF position. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.

Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks. This step may take up to 30 seconds. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).

Turn the ignition switch to the ON position in order to exit the transmitter programming mode. Mar 05, 2010 . Try to reprogram the remotes to the alarm.